Battery Cycler
7100 Series Battery Cell Tester

The 7100 series is designed to meet the demands of testing cell-level batteries for existing and future generations.

Read More

Battery Cycler
Battery Cycler

EV Battery cyclers for charge, discharge and lifecycle testing of EV battery packs and modules. High voltages and currents for electric vehicle testing.

Read More

Battery-Emulator
Battery Simulator / Emulator

EV Battery simulators / emulators for testing electric vehicle propulsion and powertrain systems, including traction inverters, E-motors and E-axles.

Read More

Universal Inverter
Universal Inverter

Unico provides modular testing solutions with its Universal Inverter to test E-motors in EV applications. Find out more about this solution

Read More

E-Motor Emulator
E-Motor Emulator

E-Motor emulators for testing electric vehicle traction inverters. Validate and test different inverter designs to prevent prototype e-motor failure.

Read More

E-Motor Dyno Drive
E-Motor Dyno Drive

Unico’s E-Motor Dynamometer Drive system has a unique design that allows the drive to operate any AC motor without the current-loop setup required by conventional drives.

Read More

E Dyno Drive
E-Drive Dyno Drive

Unico’s E-Drive Dynamometer Drive system provides internal inertia simulation, that simulates both fixed and dynamic inertias using internal models or external commands.

Read More

E-Axele-Dyno-Drive
E-Axle Dyno Drive

Unico’s E-Axle Dynamometer Drive system has a torque estimator that eliminates the need for expensive and mechanically complicated torque-measuring devices.

Read More

Hybrid-Dyno-Drive
Hybrid Electric Dyno Drive

Unico’s Hybrid Electric Dynamometer Drive system smoothly switches from speed mode to torque mode and back using controlled transitions and programmable ramp rates.

Read More

Chassis-Dyno-Drive
Chassis Dyno Drive

Unico’s E-Drive Dynamometer Drive system has full regeneration to the three-phase power grid. The drive can be configured for ultra-quiet operation required for NVH testing.

Read More

...
Engine Dyno Drive

Unico’s E-Motor Dynamometer Drive system is a proven platform installed throughout the world for durability, validation and high-performance engine testing applications.

Read More

...
Transmission Dyno Drive

Unico’s Transmission Dynamometer Drive system simulates the real-time torque pulses produced by internal combustion engines. Scalable design for complete 4WD test rigs.

Read More

...
Feed-to-Stop Control

The FTS™ software module from Unico provides automated feeding control for roll-feed applications which enables users to take full advantage of the machine.

Read More

...
Flying Cutoff Control

Unico provides Flying Cut-off control used for flying cutoff die accelerator drive system with the best-in-class flexibility and reliability required for coil processing applications.

Read More

...
Loop/Leveler Control

The Unico Loop/Leveler Control systems for coil processing applications are developed for the optimal control of the leveler and straightener in order to explicitly handle important control specifications.

Read More

...
Metal Rotary Cutoff Control

Unico provides Metal Rotary Cut-off specifically for controlling rotary-cutoff applications with the best-in-class flexibility and reliability required for the metal industry.

Read More

...
Position Indexer Control

Unico provides Position/Indexer Control PIC™ software specifically for controlling linear- or rotary-indexer applications with the best-in-class flexibility and reliability.

Read More

...
Press / Sheer Control

Press / Shear Control PSC™ software from Unico allows swift control of press and shear applications in the metal industry. It comes with best-in-class flexibility and reliability.

Read More

...
Uncoiler / Recoiler with Tension Control

The Unico Uncoiler / Recoiler with Tension Control URC™ software module provides superior control of unwinding and rewind applications in the metal industry.

Read More

...
Embedded Profile Control

The Unico Embedded Profile Control system is a scalable motion control system designed specifically for metal forming applications. It provides coordinated motion control for up to 20 drives in as many as 20 independent axes in its standard configuration.

Read More

...
STF® Servo Transfer Feed

The standard STF® system provides coordinated motion control for as many as 16 drives in four independent axes, while custom systems can control a virtually unlimited number of drives and axes. The servo system provides electronic line shafting that eliminates the large gearboxes...

Read More

...
SRP Variable Speed Drive

Unico’s SRP sucker rod pump drive provides unmatched autonomous production optimization, equipment protection, energy efficiency, and remote well analytics to maximize the performance of your well. It features fast acting intra-stroke control with reliable, hands-off, self-adjusting operation to unburden your operators.

Read More

...
ESP Variable Speed Drive

Unico’s ESP electric submersible drive provides rugged and reliable motor control with advanced automation, featuring high efficiency, low harmonics, and best-in-class motor and pump protection.

Read More

...
PCP Variable Speed Drive

Unico’s PCP progressive cavity pump drive provides precision torque and speed control with advanced features, protecting the rod-string while providing controlled backspin and power-loss ride-thru. Sensor-less fluid level estimate and control protects against pump-off. Downhole modelling provides inferred pump load and velocity for pump diagnostics including stick/slip identification.

Read More

...
Rod Pump Controller

Excluding a VSD, but using the same control board as an SRP VSD, Unico’s stand-alone RPC sucker rod pump controller includes many of the same features as our SRP drive, including enhanced start/stop pump-off control using surface and downhole dynamometer plots. It supports traditional and hydraulic pumping unit. Engine control is optional.

Read More

...
Linear Rod Pump

Unico’s LRP® sucker-rod pumping unit is an alternative to traditional horsehead units, featuring a streamlined design, safety, small footprint, and sophisticated automation to maximize well production and extend downhole equipment life.

Read More

...
Crank Rod Pump

Unico’s CRP® sucker-rod pumping unit is a compact, short stroke, crank driven unit designed specifically for shallow, low-flow coal-bed methane and stripper wells. Its full-featured SRP software includes patented Flat Power and solar MPPT, making it a perfect fit for 100% PV solar operation for off-grid and remote locations.

Read More

...
Well Analytics

Well Analytics System by Unico is an efficient, cost-effective way for oil and gas producers to stay connected to the most critical aspects of daily operations.

Read More

...
Real Time Monitoring

The GMC® system continuously collects data from an unlimited number of wells and fields and makes that data accessible from virtually anywhere at any time over the Web.

Read More

...
Notification and Alarms

A sophisticated subscription service alerts users when specific conditions are detected. Notifications can be triggered, for example, whenever a fault occurs, when specific...

Read More

...
Automated Well Reports

Comprehensive well reports can be generated automatically or on demand. SRP reports include both surface and downhole dynamometer graphs. Users can simultaneously compare...

Read More

...
Double Facer / Backer Control

The double facer/baker control drive from Unico improves the production process of paper conversion while providing complete safety from wear with advanced controls and diagnostics.

Read More

...
Pull Roll Control

For an economical and highly effective choice for your paper converting needs, look no further than the Unico Pull Roll Control drive.

Read More

...
Rotary Cutoff Control

Controlling the rotary cut-off during production has become much easier with the Unico smart and easy rotary cut-off control.

Read More

...
Single Facer Control

The single facer control drive from Unico provides the best control options for paper converting applications. It can help users to automate and optimize the manufacturing process.

Read More

...
Slitter / Scorer Control

Along with multiple manual and automatic modes, the Unico slitter scorer control drive is equipped with the latest technology to perform every task with more efficiency.

Read More

...
Web AOC Shear Control

Unico’s Smart Web AOC Shear Drive can be used alone or as part of a multidrive corrugator dry-end system. The drive controls the shear during the automatic-order change (AOC) sequence and scrap chop-out

Read More

...
Feed to Register Control

Get the control at your fingertips with Unico smart and automatic feed to register control drive and become a paper converting industry expert.

Read More

...
Rotary Die Cutter Control

The Unico rotary die clutter control drive equipped with modern tech makes your paper converting methods easier, fast, reliable, and more flexible.

Read More

...
Rotary Printer Control

The Unico Rotary Printer Control drive can help you make your paper converting process more explicit, manageable, fast, and firm with advanced software control and digital technology.

Read More

...
Sheeter Control

Unico’s high-performance sheeter control systems provide comprehensive solutions at low cost and more flexibility. Our sheeter control yields optimal cut accuracy, throughput, and energy savings with paper and board applications.

Read More